Product introduction:
2: Polyethersulfone (PES) folding filter----sterilization type fine filter
3: Polytetrafluoroethylene (PTFE) folding filter----High temperature gas sterilization type fine filter
4: nylon membrane (N66) folding filter----sterilization type fine filter
5: Polyvinylidene fluoride film (PVDF) folding filter----sterilization type fine filter.
B type <80 °C pressure difference 2bar----high temperature resistant material
C type <95 ° C pressure difference 1 bar --- imported polypropylene and stainless steel
D type <125 °C pressure difference 1bar---- PVDF material
Flow: 0.5 M3 per 10 inches
Applicable pH: 1-13.
Maximum pressure difference: 25 ° C, forward 0.4 Mpa, reverse 0.2 Mpa.
Working temperature: at 0.25Mpa,
a, general type <70 ° C
b, high temperature type <90 ° C.
Sterilization: Tolerance to 126 ° C, 30 minutes on-line steam sterilization.
Endotoxin: The water extract of the filter column was tested by lAL and the endotoxin content was less than 0.5 EU/ml.
Food industry: filtration of alcohol, beverages and drinking water.
Electronics industry: Pre-filtration of pure water and ultrapure water.
Petroleum and chemical industry: filtration of various organic solvents, acids and lye, oilfield water filtration
This filter element can provide international standard 222, 226, flat seal, fin and other standard interface forms, as well as 10 inch, 20 inch, 30 inch lengths. Customized for the number of layers and length of the filter for customers with special needs.
The microporous filter element is a deep filter element that is commonly used for preheating, clarification and end filtration of liquids. It has the following characteristics: ultra-fine polypropylene fiber membrane as filter medium, low pressure difference, high throughput, good filtration precision, low economic cost, all polypropylene structure, end cap, shell and center rod are made of polypropylene Material; melted by hot melt process, that is, PP and PP are self-melted and bonded without any binder; have wide chemical compatibility; have a series of pore diameters and various interface forms.
Product Categories:
1: Polypropylene (PP) Folding Filter Core----General-purpose fine filter2: Polyethersulfone (PES) folding filter----sterilization type fine filter
3: Polytetrafluoroethylene (PTFE) folding filter----High temperature gas sterilization type fine filter
4: nylon membrane (N66) folding filter----sterilization type fine filter
5: Polyvinylidene fluoride film (PVDF) folding filter----sterilization type fine filter.
Working temperature and pressure difference:
Type A <60°C differential pressure 2bar----polypropyleneB type <80 °C pressure difference 2bar----high temperature resistant material
C type <95 ° C pressure difference 1 bar --- imported polypropylene and stainless steel
D type <125 °C pressure difference 1bar---- PVDF material
Flow: 0.5 M3 per 10 inches
Features:
Made of 100% polypropylene without any binder, minimizing the dissolution of the filter column itself. Excellent chemical compatibility for filtration of strong acids, bases and organic solvents. The filter membrane is deep-filtered, which has strong dirt holding capacity and long service life. High temperature resistance, can withstand repeated high temperature and high pressure sterilization, or continuous use at high temperatures.Technical Parameters:
Filtration accuracy: 0.22m, 0.45m, 1m, 3m, 5m, 10m, 20m, 30m.Applicable pH: 1-13.
Maximum pressure difference: 25 ° C, forward 0.4 Mpa, reverse 0.2 Mpa.
Working temperature: at 0.25Mpa,
a, general type <70 ° C
b, high temperature type <90 ° C.
Sterilization: Tolerance to 126 ° C, 30 minutes on-line steam sterilization.
Endotoxin: The water extract of the filter column was tested by lAL and the endotoxin content was less than 0.5 EU/ml.
Application areas:
Pharmaceutical industry: Prefiltration of various injections, liquids and injections of bottled water, pre-filtration of large infusions and various antibiotics and traditional Chinese medicine injections.Food industry: filtration of alcohol, beverages and drinking water.
Electronics industry: Pre-filtration of pure water and ultrapure water.
Petroleum and chemical industry: filtration of various organic solvents, acids and lye, oilfield water filtration
This filter element can provide international standard 222, 226, flat seal, fin and other standard interface forms, as well as 10 inch, 20 inch, 30 inch lengths. Customized for the number of layers and length of the filter for customers with special needs.